Thermalseal Rts Sealing Films Are Based on 50 µ M Polyolefin Films with 50 µ M Inert Encapsulated Silicone Adhesive

• Disposable: Disposable
• Certification: CE, ISO, FDA
• Reactant State: Solid
• Model NO.: 61-0210 61-0250
• Material: Polyolefin
• Dnase & Rnase Free: Yes
• Application: Used for Qpcr, Storage & Crystallization
• Temperature Range: -70 °c to - 100 °c
• Transport Package: 100 /Case
• Trademark: BIOLOGIX
• Origin: Changzhou City, Jiangsu Province, China

Product Description

ThermalSeal RTS sealing films are based on 50 µm polyolefin films with 50 µm inert encapsulated silicone adhesive. 

 

 

Characteristic

 

-- 50 µm polyolefin films

-- 50 µm inert encapsulated silicone adhesive

-- Dimensions 78.6 by 139.7 mm

-- Length 113.0 mm

-- Recommended for temperatures from-70 °C to +100 °C

-- Used for qPCR, storage & crystallization

-- High optical clarity

-- Minimal to no autofluorescence

-- Chemically inert; no extractables except at extreme pH

-- DMSO resistant for HTS

-- Heat resistant, recommended for temperatures from

-- Certified DNase-, RNase-, and nucleic-acid-free

-- Fit within raised plate rim to prevent loss of seal due to film lifting

-- Silicone adhesive forms the strongest available seal for evaporation prevention

-- Non-tacky adhesive layer simplifies handling of film prior to sealing

 

Ordering Information

 

Cat #	Description	Quantity
61-0210	ThermalSeal RTS Sealing Films, Non-Sterile	100
61-0250	ThermalSeal RTS Sealing Films, Sterile	50

1.What are the main factors that influence the maximum centrifugal acceleration force?
Use of organic solutions, temperature below 0°C, centrifuging without centrifuge adapter, etc. Conduct a trial run to determine proper conditions before any critical use begins.
The RCF (relative centrifugal force) or G ratings for our disposable centrifuge tubes have been established at room temperature using tubes filled to nominal capacity with water and centrifuging for 30 minutes. recommended carriers, adapters, and cushions that fully support the tubes. If an angle head rotor is used or proper support is not provided, G values will be lower.
Do not confuse speed or revolutions per minute (RPM) with relative centrifugal force (RCF). Instructions for centrifuging a sample at a given RPM and time are incomplete unless the rotor or radius is specified. Protocols should always state the time and RCF value for centrifuging a sample.
2.What are autoclaving guidelines of plastics?
To ensure successful steam sterilization of your plastic labware please adhere to the following guidelines: PLEASE NOTE THAT NOT ALL PRODUCTS ARE AUTOCLAVABLE. Autoclave plastic consumables at 121°C and 15psi/1 atm for 15 minutes. Do not use a dry cycle, as this may cause deformation or weakening of the plastic. Allow temperature within the autoclave to return to 80°C or below before removing products.
3.What are Biologix's Commitments to Quality?
We look at quality from every angle in terms of functionality, safety, purity, formulation, consistency, manufacturing, customer service, technical support, and much more. According to the detailed QA/QC procedures for our manufacturing facility, each and every product is traceable by lot, regardless of packaging format. Products must go through a five-step human inspection before being released for packaging. Biologix applies the most stringent standards to certify that products are free from RNase, DNase, endotoxin (pyrogens), etc. In addition to being ISO 9001:2008, CE compliant, we also make available to our customers lot-specific certificates such as Sterilization Certificates, Nuclease Free Certificates, Certificates of Origin, etc.