Transfer Pipets of Liquids Available in 1ml and 3ml Volumes Molded Graduations

• Disposable: Optional
• Certification: CE, ISO
• Power Source: Manual
• Model NO.: 30-0135/ 30-0135A1 / 30-0138/ 30-0138A1
• Material: Rubber / Plastic
• Sterilized: Gamma
• Pipet Design: Clearly Visible with Either Clear or Opaque Samp
• Transport Package: Bulk Packaged and Individually Wrapped
• Specification: Available in 1ml and 3ml volumes
• Trademark: BIOLOGIX
• Origin: Changzhou, Jiangsu, China.
• HS Code: 3917310000

Product Description

                                                                                         Transfer Pipets

I. APPLICATIONS
1. General purpose transfer of liquids

II. FEATURES
1. Material: flexible polyethylene
2. For general purpose
3. Transparent wall permits easy viewing of pipet contents
4. 100% inert

III. PIPET DESIGN
1. Available in 1ml and 3ml volumes
2. Molded graduations
3. Clearly visible with either clear or opaque samples

IV. PACKAGING
1. Bulk packaged and Individually wrapped, 500 pipets/pack and 4 packs/case

 

V. DESCRIPTION 
 

Cat #	Length	Graduated To	Sterile	Package	Unit
30-0135	162.0mm	1ml	NO	Bulk	500 Pieces/Pack, 4 Packs/Case
30-0135A1	162.0mm	1ml	YES	Individually Wrapped	500 Pieces/Pack, 4 Packs/Case
30-0138	162.0mm	3ml	NO	Bulk	500 Pieces/Pack, 4 Packs/Case
30-0138A1	162.0mm	3ml	YES	Individually Wrapped	500 Pieces/Pack, 4 Packs/Case
30-0238A1	183.0mm	3ml	YES	Individually Wrapped	500 Pieces/Pack, 4 Packs/Case

 

1.What are the main factors that influence the maximum centrifugal acceleration force?

Use of organic solutions, temperature below 0°C, centrifuging without centrifuge adapter, etc. Conduct a trial run to determine proper conditions before any critical use begins.
The RCF (relative centrifugal force) or G ratings for our disposable centrifuge tubes have been established at room temperature using tubes filled to nominal capacity with water and centrifuging for 30 minutes. recommended carriers, adapters, and cushions that fully support the tubes. If an angle head rotor is used or proper support is not provided, G values will be lower.
Do not confuse speed or revolutions per minute (RPM) with relative centrifugal force (RCF). Instructions for centrifuging a sample at a given RPM and time are incomplete unless the rotor or radius is specified. Protocols should always state the time and RCF value for centrifuging a sample.

2.What are autoclaving guidelines of plastics?

To ensure successful steam sterilization of your plastic labware please adhere to the following guidelines: PLEASE NOTE THAT NOT ALL PRODUCTS ARE AUTOCLAVABLE. Autoclave plastic consumables at 121°C and 15psi/1 atm for 15 minutes. Do not use a dry cycle, as this may cause deformation or weakening of the plastic. Allow temperature within the autoclave to return to 80°C or below before removing products.

3.What are Biologix's Commitments to Quality?
We look at quality from every angle in terms of functionality, safety, purity, formulation, consistency, manufacturing, customer service, technical support, and much more. According to the detailed QA/QC procedures for our manufacturing facility, each and every product is traceable by lot, regardless of packaging format. Products must go through a five-step human inspection before being released for packaging. Biologix applies the most stringent standards to certify that products are free from RNase, DNase, endotoxin (pyrogens), etc. In addition to being ISO 9001:2008, CE compliant, we also make available to our customers lot-specific certificates such as Sterilization Certificates, Nuclease Free Certificates, Certificates of Origin, etc.